336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Hydraulic Oil Cooler - Remove and Install Caterpillar


Hydraulic Oil Cooler - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
138-7575  Link Brackets 
Loctite 242 

Start By:

  1. Release the hydraulic system pressure.

------ WARNING! ------

Personal injury can result from hot coolant, steam and alkali.

At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.

Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.

Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.

Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.


  1. Turn the battery disconnect switch to the OFF position.

  2. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures.

  3. Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for correct draining and filling procedure.


    Illustration 1g02346242

  4. Remove sheet assembly (1), hose (2), coolant tank (3), and guard assembly (4).


    Illustration 2g02346243

  5. Loosen clamps (5).

  6. Loosen clamp (6) and reposition shroud seal (7).


    Illustration 3g02346244

  7. Remove bolts (8) and sheet assembly (9).


    Illustration 4g02346370

  8. Loosen clamps (11) and (12). Reposition clamps (11) and (12).

  9. Disconnect hose (10).


    Illustration 5g02346369

  10. Remove bolts (16) and reposition shroud assembly (17).

  11. Remove bolts (13), bolts (14), and bracket assembly (15).


    Illustration 6g02346371


    Illustration 7g02346372

  12. Disconnect hose (19).

  13. Attach Tooling (A) and a suitable lifting device to hydraulic oil cooler (18). The weight of hydraulic oil cooler (18) is approximately 71 kg (157 lb).

  14. Remove bolts (20) and hydraulic oil cooler (18).

Installation Procedure

  1. Install hydraulic oil cooler (18) in the reverse order of removal.

    1. Tighten bolts (20) and bolts (14) to a torque of 35 to 40 N·m (26 to 30 lb ft).

    2. Apply Tooling (B) to the threads of bolts (8).

Information System:

Inspection of Rear Engine Mounts on 3500 Family of Engines {1152, 1154}
Installation Procedure for 251-0529 Cab Wiring Gp on Certain Hydraulic Excavators {1408}
Installation Procedure for 239-8695 Hydraulic Pedal Control Gp {5059, 5063}
349F and 352F Excavators Machine System Relief Valve (Line)
2010/05/12 Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
C15 and C18 Engines for Caterpillar Built Machines Fuel Pressure Regulator - Remove and Install
2010/03/29 Procedure to Disengage the Cable Assembly Prior to Removing the Front Window on Certain Excavators {7310}
C9.3 Tier 4 Final Engines Electric Starting System - Test
349E Excavator Hydraulic System Solenoid Valve (Proportional Reducing) - Power Shift System
(Custom) Hydraulic Buckets for Wheel Loaders, Integrated Toolcarriers, and Track Loaders Specifications
349E Excavator Hydraulic System Relief Valve (Main)
2010/03/24 Improvements Have Been Made to Bulk Hose for Certain Caterpillar Products {5057}
Installation Procedure for 259-5045 Combined Flow Wiring Gp {1408}
Installation Procedure for 260-7986 Pilot Lines Gp {5057, 5059}
Installation Procedure for the 260-8008 Front Lines Gp {5057}
349F and 352F Excavators Machine Systems Shuttle Valve - Remove and Install - Straight Travel
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0041 - FMI 03
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Symptom Troubleshooting
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0041 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0168 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0168 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0191 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0247 - FMI 09
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0262 - FMI 03