Engine Oil Cooler - Remove and Install
`
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
[UENR7319]
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Turbocharger - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Engine Oil Pump - Remove and Install
COOLING SYSTEM
COOLER GP
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove and Install
307 Hydraulic Excavator Engine Supplement
Engine Oil Cooler - Remove and Install
306 and 306.5 Mini Hydraulic Excavator Engine Supplement
Engine Oil Cooler - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 1 g06003514 - Remove engine oil filter (1).
Show/hide table
Illustration 2 g06003538 - Remove clamp (3) and clamp (5). Disconnect hose assembly (2) and hose assembly (4).
- Remove connector (7), engine oil cooler (6), and the collar.
- Install engine oil cooler (6) in the reverse order of removal.
- Tighten connector (7) to a torque of
40 N·m to 44 N·m (30 lb ft to 32 lb ft) .
- Tighten connector (7) to a torque of
Information System:
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Turbocharger - Remove and Install
320D2 GC Excavator Machine Systems
Bucket Linkage Bearings and Seals - Remove and Install
314D CR Hydraulic Excavator Machine Systems
Recoil Spring - Assemble
320D2 GC Excavator Machine Systems
Bucket Linkage - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Electronic Unit Injector - Remove and Install
320D2 GC Excavator Machine Systems
Bucket - Remove and Install
320D2 GC Excavator Machine Systems
Duo-Cone Conventional Seals - Install
320D2 GC Excavator Machine System Specifications
Swing Gear and Bearing
307E2 Mini Hydraulic Excavator Machine Systems
Hydraulic Lockout Control - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Return Hydraulic System
320D2 GC Excavator Machine System Specifications
Upper Frame
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Fuel Manifold (Rail) - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Engine Oil Pump - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Flywheel - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Cylinder Head - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
312F and 313F Excavator Machine Systems
Electronic Control (Pilot System)
312F and 313F Excavator Machine Systems
Electronic Control (Main Pump System)
318F Excavator Machine Systems
Stick - 2.25 m (7.381 ft)
312F and 313F Excavator Machine System Specifications
Fuel Tank
312F and 313F Excavator Machine System Specifications
Swing Gear and Bearing
318F Excavator Machine Systems
Stick - 3.1 m (10.17 ft)
312F and 313F Excavator Machine System Specifications
Swing Drive Mounting
318F Excavator Machine Systems
Stick - 2.6 m (8.53 ft)