Stick Bearings and Seals - Install
`
325F Excavator Machine Systems
[UENR6794]
325F Excavator Machine Systems
Stick Bearings and Seals - Remove
325F Excavator Machine Systems
Stick - Install
IMPLEMENTS
STICK GP
325F Excavator Machine Systems
Stick - Remove
325F Excavator Machine Systems
Stick Bearings and Seals - Remove
325F Excavator Machine Systems
Stick Bearings and Seals - Install
325F Excavator Machine Systems
Stick - Install
1.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Gp | 1 |
B | 452-6006 | Molybdenum Grease | - |
- Make sure that the bores for the bearings are free of paint and grease prior to the installation of the bearings. Coat the bearings and the bearing bores with Tooling (B) prior to the installation of the bearings in the bores. Bearings must be installed with the identification numbers toward the outside of the stick.
Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.
Show/hide tableIllustration 1 g00687562 (S) Stick
(T) Sleeve Bearing - Lower the temperature of the sleeve bearing to
−40 °C (−40 °F) . Use Tooling (A) to install the sleeve bearing in the bore for the stick to bucket pin. Install the sleeve bearing until Dimension (X) is9.5 ± 0.8 mm (0.37 ± 0.03 inch) .Show/hide tableIllustration 2 g00604131 - Use Tooling (A) to install lip seal (2) in the bore for the stick to bucket pin. Install the lip seal with the sealing lip toward the outside of the stick. Install the lip seal until the lip seal makes contact with the sleeve bearing.
- Repeat Steps 2 and 3 to install the sleeve bearing and the lip seal on the opposite side of the stick.
Show/hide table
Illustration 3 g00687582 (S) Stick
(U) Sleeve Bearing - Lower the temperature of the sleeve bearing to
−40 °C (−40 °F) . Use Tooling (A) to install the sleeve bearing in the bore for the stick to boom pin. Install the sleeve bearing until Dimension (Y) is9.5 ± 0.8 mm (0.37 ± 0.03 inch) .Show/hide tableIllustration 4 g00592359 - Use Tooling (A) to install lip seal (1) in the bore for the stick to boom pin. Install the lip seal with the sealing lip toward the outside of the stick. Install the lip seal until the lip seal makes contact with the sleeve bearing.
- Repeat Steps 5 and 6 to install the sleeve bearing and the lip seal on the opposite side of the stick.
- Apply a thin coat of Tooling (B) on the sleeve bearings. Apply a thin coat of Tooling (B) on the lips of the lip seals (1) and (2).
End By:
- Install the stick.
Information System:
325F Excavator Machine Systems
Stick Bearings and Seals - Remove
325F Excavator Machine Systems
Stick - Remove
910K, 914K and 920K Compact Wheel Loaders
Bucket Tips - Inspect/Replace
325F Excavator Machine Systems
Stick Cylinder - Remove and Install
300.9D VPS Mini Hydraulic Excavator Machine Systems
Auxiliary Hydraulic System
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Boom Hydraulic System
910K, 914K and 920K Compact Wheel Loaders
Operation Information
318F Excavator Machine Systems
Front Lines
316F Excavator Machine System Specifications
Pilot Lines (Main Pump)
Exhaust Gas Valve (NRS) for C7.1, and C6.6 Engines {5137}
312F and 313F Excavator Machine Systems
Travel System
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Main)
Installation of the <NOBR>501-2518</NOBR> Auxiliary Control Ar (Tool Control) on Certain Hydraulic Excavators {1408, 5051, 5057, 7405, 7557}
Installation of the <NOBR>501-2517</NOBR> Auxiliary Control Ar (Tool Control) on Certain Hydraulic Excavators {1408, 5051, 5057, 5059, 7301, 7405, 7557}
Installation Procedure for the <NOBR>330-2397</NOBR> Front Lines Gp on Certain Hydraulic Excavators {5057}
Installation Procedure for the <NOBR>416-5026</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
Installation Procedure for the <NOBR>418-1101</NOBR> Chassis Wiring Gp On Certain Hydraulic Excavators {1408}
Installation Procedure for the <NOBR>437-0403</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
325F Excavator Machine Systems
Stick - Install
Installation Procedure for the <NOBR>330-2400</NOBR> Front Lines Gp on Certain Hydraulic Excavators {5057}
Installation of the 486-0608 Coupler Control Ar on Certain Hydraulic Excavators {6129, 7332, 7405, 7557}
Installation of the 467-6748 Chassis Wiring Gp On Certain Hydraulic Excavators {6129}
300.9D VPS Mini Hydraulic Excavator Machine Systems
Swing Hydraulic System
Procedure to Install a 455-6307 Gear Pump Group on Certain M318D MH and M322D MH Material Handlers {5073}