Crankshaft Gear - Remove and Install
`
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
[UENR7319]
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Camshaft - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft - Remove
BASIC ENGINE
CRANKSHAFT GP
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft Pulley - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft - Remove
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Crankshaft - Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tooling | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-2321 | Puller Assembly | 1 |
Start By:
- Remove idler gear.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove crankshaft collar (2), oil slinger (1), and the O-ring seal.
Show/hide table
Illustration 2 g06014764 - Use Tooling (A) to remove crankshaft gear (3).
Show/hide table
| |
| Illustration 1 | g06014755 |
- Install crankshaft gear (3) in the reverse order of removal.
Note: The crankshaft gear (3) taper needs to face toward the cylinder block when installed.
Information System:
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Main Hydraulic System
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Camshaft - Remove and Install
325F Excavator Machine Systems
Drift Reduction Valve (Stick) - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Specifications
New Machine Software is Now Used on Certain Excavators {7610, 7620}
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Gear Pump (Pilot) - Test
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Pump Control (Negative Flow) - Test
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Pump Control (Output Flow) - Adjust
Improved Ignition Circuit Wiring is Now Used for Certain 568 Forestry Machines {1408, 7301}
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Main Pump (Flow) - Test - Constant Horsepower Flow Control
A New Stick Cylinder Group is Now Used on Certain 568 Forestry Excavators {5458}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Idler Gear - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Pilot Hydraulic System
990K Wheel Loader and 844K Wheel Dozer Machine Systems
Seat - Remove and Install
312F and 313F Excavator Machine Systems
Swing System
300.9D VPS Mini Hydraulic Excavator Machine Systems
Return Hydraulic System
816K Landfill Compactor
Sound Information and Vibration Information
814 Wheel Dozer
Differential and Final Drive Oil - Change
814 Wheel Dozer
Differential and Final Drive Oil Level - Check
314F and 315F Excavators Machine Systems
Pilot System
314F and 315F Excavators Machine Systems
Swing System
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Main Hydraulic Pump
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Speed Signal - Test
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System
Main Control Valve