416E, 420E and 430E Backhoe Loaders Operational Checks (Transmission) Caterpillar


Operational Checks (Transmission)
`
1.1. Operational Checks (Transmission)

------ WARNING! ------

Sudden movement of the machine or release of oil under pressure can cause injury to persons on or near the machine. To prevent possible injury, perform the procedure that follows before the test is done.

----------------------

Operational Checks (Transmission)

The operational checks can be used to find leakage in the system and components that are not functioning correctly. The operational checks can be used to determine whether the pumps are functioning properly. The operational checks can also be used to ensure that the clutches properly engage through all SPEEDS. When you perform the operational checks, check for the following conditions:

  • Abnormal noises in the transmission

  • Abnormal noises in the pumps

  • Abnormal engagement in the clutches through all SPEEDS

After you have completed the operational checks, inspect the power train for any leaking components, damaged components or worn components.

ReferenceRefer to the service manual module Troubleshooting, RENR6488, "Transmission" for further information concerning a problem and probable causes.

  1. Start the engine and allow the transmission oil temperature to reach the normal operating temperature.

  1. Operate the machine in the FORWARD direction and in the REVERSE direction while the machine is in the AUTOSHIFT mode. Operate the machine in all speeds for both directions. Ensure that the machine operates in both directions and all speeds.

  1. Operate the machine in all speeds while the machine is in the MANUAL mode. Use the transmission direction and speed control lever in order to operate the machine in all speeds. Operate the machine in both the FORWARD and the REVERSE directions. Ensure that the machine operates in both directions and all speeds.

  1. Stop the machine. Stop the engine. Inspect the power train components for any damaged parts or leakage.

Information System:

416E, 420E and 430E Backhoe Loaders Operational Checks (Steering System)
416E, 420E and 430E Backhoe Loaders Operational Checks (Brake System)
330D and 336D Excavators and 330D Material Handlers Machine System Specifications Boom Cylinder
C6.6 Industrial Engine Power Sources
C6.6 Industrial Engine Electronic Control System
C4.4 Industrial Engine Glossary of Electronic Control Terms
C6.6 Industrial Engine Air Inlet and Exhaust System
C6.6 Industrial Engine Basic Engine
416E, 420E and 430E Backhoe Loaders Operational Checks (Axle, Differential)
416E, 420E and 430E Backhoe Loaders Machine Preparation for Troubleshooting
416E, 420E and 430E Backhoe Loaders Location of Electrical Components
416E, 420E and 430E Backhoe Loaders Hydraulic System
416E, 420E and 430E Backhoe Loaders Power Supply Circuit of Electronic Control Module
416E, 420E and 430E Backhoe Loaders Service Tools
416E, 420E and 430E Backhoe Loaders Steering System
416E, 420E and 430E Backhoe Loaders Switch Circuits
416E, 420E and 430E Backhoe Loaders Visual Inspection
416E, 420E and 430E Backhoe Loaders Transmission - Standard Shift
416E, 420E and 430E Backhoe Loaders Using Caterpillar Electronic Technician to Determine Diagnostic Codes
416E, 420E and 430E Backhoe Loaders Using Advisor to Determine Diagnostic Codes
416E, 420E and 430E Backhoe Loaders System Schematic
328D CR Excavator Boom/Stick/Bucket Combinations
2010/07/08 The Configuration of the 320D Engine Arrangement Has Been Updated for the Fan Drive System {1359}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Check Valve (Cooler Bypass) - Remove and Install