416E, 420E and 430E Backhoe Loaders MID 039 - CID 1406 - FMI 06 Caterpillar


MID 039 - CID 1406 - FMI 06
`

Conditions Which Generate This Code:




Illustration 1g01217334

Schematic of the "Solenoid Valve (No. 6) (speed 3)"

This diagnostic code is associated with the "Solenoid Valve (No. 6) (speed 3)". The FMI 06 diagnostic code means that the ECM has determined that there is a short to ground in the solenoid circuit.

The possible causes of this diagnostic code are listed below:

  • The energize circuit of the solenoid is shorted to ground.

  • The solenoid has failed.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1406 FMI 06 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

The transmission will be placed in the Neutral gear until the diagnostic has been corrected.

Test Step 1. CHECK THE SOLENOID.

  1. Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.

  1. Observe the status of the diagnostic code.

  1. Disconnect the solenoid with the active diagnostic code from the machine harness.

Expected Result:

The CID 1406 FMI 06 diagnostic code changes to a CID 1406 FMI 05 diagnostic code when the solenoid is disconnected.

Results:

  • YES - The CID 1406 FMI 06 diagnostic code changes to a CID 1406 FMI 05 diagnostic code when the solenoid is disconnected. The circuit is correct.

    Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.

    STOP

  • NO - The CID 1406 FMI 06 diagnostic code remains active. Proceed to Test Step 2.

Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. The solenoid remains disconnected from the machine harness.

  1. Disconnect the machine harness connector(s) from the ECM.

  1. At the machine harness connector, measure the resistance from the signal contact J2-7 (wire 902-BR) to all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-7 (wire 902-BR) and the circuit with the low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.

  1. Inspect the harness connectors and clean the contacts of the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Check the status of the CID 1406 FMI 06 diagnostic code.

Expected Result:

The CID 1406 FMI 06 diagnostic code is active.

Results:

  • YES - The CID 1406 FMI 06 diagnostic code is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 1406 FMI 06 diagnostic code is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Information System:

416E, 420E and 430E Backhoe Loaders MID 039 - CID 1406 - FMI 05
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1406 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1405 - FMI 06
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1405 - FMI 05
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1405 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1404 - FMI 06
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1404 - FMI 05
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1404 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1403 - FMI 06
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1403 - FMI 05
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1403 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1402 - FMI 06
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1482 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1482 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1529 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1529 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1834 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 08
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 04