416E, 420E and 430E Backhoe Loaders MID 039 - CID 0600 - FMI 04 Caterpillar


MID 039 - CID 0600 - FMI 04
`

Conditions Which Generate This Code:




Illustration 1g01528642

Schematic Of The Hydraulic Oil Temperature Sensor

This diagnostic code is associated with the hydraulic oil temperature sensor. The FMI 04 means that the ECM has determined that the voltage of the circuit for the position sensor is below normal.

The possible causes of this diagnostic code are listed below:

  • The signal circuit for the sensor is shorted to ground.

  • The sensor has failed.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0600 FMI 04 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

The diagnostic code of CID 0600 FMI 04 will be logged in the internal memory of the Machine ECM.

Test Step 1. CHECK THE SENSOR

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Ensure that the diagnostic code is active.

  1. Observe the status of the diagnostic code. Disconnect the sensor from the machine harness.

Expected Result:

The CID 0600 FMI 04 remains active. The FMI has not changed and the "04" is still active.

Results:

  • OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.

  • NOT OK - The diagnostic code is no longer active. The sensor has failed.

    Repair: Replace the sensor.

    STOP

Test Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness from the sensor.

  1. Disconnect the machine harness connector(s) from the ECM.

  1. At the machine harness connector for the ECM, measure the resistance from the signal contact J1-29 (wire 442-GY) of the machine harness to all possible sources of ground. Measure the resistance to all contacts of the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - One or more resistance measurements is not correct. There is a short in the machine harness.

    Repair: The short is between signal contact J1-29 (wire 442-GY) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.

  1. Inspect the contacts of the harness connectors and clean the contacts.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Check the status of the CID 0600 FMI 04.

Expected Result:

The CID 0600 FMI 04 diagnostic code is active.

Results:

  • YES - The CID 0600 FMI 04 diagnostic code is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 0600 FMI 04 diagnostic code is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Information System:

416E, 420E and 430E Backhoe Loaders MID 039 - CID 0600 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0590 - FMI 12
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0590 - FMI 09
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0590 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0490 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0490 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0368 - FMI 04
2010/07/08 Service Allowance Pressure Settings are Available for Setting the Main Relief Valve and the Line Relief Valves for Certain Excavators {5069, 5117}
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0368 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0367 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0262 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0262 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0626 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0629 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0668 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0668 - FMI 09
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0668 - FMI 12
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0702 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 0871 - FMI 09
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1009 - FMI 03
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1009 - FMI 04
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1037 - FMI 02
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1037 - FMI 09
416E, 420E and 430E Backhoe Loaders MID 039 - CID 1037 - FMI 12