924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Diagnostic Trouble Codes Caterpillar


Diagnostic Trouble Codes
`
1.1. Component Identifier (CID) and Failure Mode Identifier (FMI) Information

The following table lists the diagnostic codes for the Graphical Display (MID 35). When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.

Component Identifier (CID) and Failure Mode Identifier (FMI) Information

Table 1
Graphical Display (MID 35) 
DTC  Description  Procedure 
967-02  Machine Application: Erratic, Intermittent, or Incorrect  CAN Data Link - Test 
967-09  Machine Application: Abnormal Update  CAN Data Link - Test 
2348-09  SAE J1939 Data Link #2: Abnormal Update  Sensor (Data Link Type) - Test 
3318-09  Machine Left Side Object Detection Sensor: Abnormal Update  Sensor (Data Link Type) - Test 
3318-11  Machine Left Side Object Detection Sensor: Failure Mode Not Identifiable  Sensor (Data Link Type) - Test 
3318-12  Machine Left Side Object Detection Sensor: Bad Device or Component  Sensor (Data Link Type) - Test 
3319-09  Machine Right Side Object Detection Sensor: Abnormal Update  Sensor (Data Link Type) - Test 
3319-11  Machine Right Side Object Detection Sensor: Failure Mode Not Identifiable  Sensor (Data Link Type) - Test 
3319-12  Machine Right Side Object Detection Sensor: Bad Device or Component  Sensor (Data Link Type) - Test 
3330-03  Machine Left Side Object Detection Sensor: Power Supply: Voltage Above Normal  Sensor Supply - Test 
3330-04  Machine Left Side Object Detection Sensor: Power Supply: Voltage Below Normal  Sensor Supply - Test 
3331-03  Machine Right Side Object Detection Sensor: Power Supply: Voltage Above Normal  Sensor Supply - Test 
3331-04  Machine Right Side Object Detection Sensor: Power Supply: Voltage Below Normal  Sensor Supply - Test 

Information System:

924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Determining Diagnostic Trouble Codes
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Diagnostic Capabilities
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Service Menu
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
314F and 315F Excavators Safety Messages
Cat<SUP>&reg;</SUP> Electronic Technician (ET) Version 2015C or Higher is Required When Installing Engine Software on a Blank Engine ECM for a C3.4B Machine Engine {7610, 7620}
Improved Expansion Tank Lines Are Now Used on Certain 568 Forest Machines {1354, 1377}
308E2 CR and 308E2 SR Mini Hydraulic Excavators Boom and Stick Linkage - Lubricate
312F and 313F Excavator Machine Systems Main Pump (Flow) - Test - Hydraulic Power
Installing The 470-5247 Dual Tilt Kit on 415F2 Industrial Loaders {5104}
312F and 313F Excavator Machine Systems Cylinder Speed - Check
312F and 313F Excavator Machine Systems Cylinder Drift - Check - Loaded Bucket
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Event Codes
Software Updates for Certain Tier 4 Final Machines {1920, 7620}
312F and 313F Excavator Machine Systems Machine System
Procedure for the Installing the <NOBR>479-2095</NOBR> Migration Kit on 316E and 318E Excavators {1000, 7000}
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (PWM) - Test
312F and 313F Excavator Machine Systems Pilot System
300.9D VPS Mini Hydraulic Excavator Machine Systems Blade Hydraulic System
312F and 313F Excavator Machine Systems Pump Control (Output Flow) - Test - One Pump Calibration (Optional Test)
312F and 313F Excavator Machine Systems Pump Control (Output Flow) - Test - Two Pump Calibration
A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Engines {108J}
Exhaust Gas Valve (NRS) for C4.4 Engines {5137}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install