312F and 313F Excavator Machine Systems Travel Motor - Test - Measurement of Case Drain Oil Caterpillar

Table 1
"Travel Motor - Test (Measurement of Case Drain Oil)"
Machine Settings	Crossover Relief Pressure		Engine Speed
Machine Settings	37500 ± 500 kPa (5439 ± 73 psi)		Engine speed dial "10" AEC switch OFF
Item	Specification⁽¹⁾	Left Travel	Right Travel
New Travel Motor	15 L/min (4.0 US gpm)	1.	1.
		2.	2.
		3.	3.
Rebuilt Travel Motor	18 L/min (4.8 US gpm)	1.	1.
		2.	2.
		3.	3.

Show/hide table

⁽¹⁾	Maximum acceptable flow

Show/hide table

Show/hide table

Introduction

Use the following procedure to measure the case drain of the travel motors.

Show/hide table

NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat^® products. Dispose of all fluids according to local regulations and mandates.

Show/hide table




Illustration 2	g02571852
Tooling (A) 198-4240 Digital Pressure Indicator Gp

Show/hide table

Show/hide table

Show/hide table

Table 3
Tool	Item	Qty	Part Number	Description
A			198-4240	Digital Pressure Indicator Gp
	A1	1	198-4234	Indicator
	A2	2	198-4239	Pressure Sensor 34,450 kPa (6,000 psi)
	A3	2	198-4236	Extension Cable
D	D1	1	6V-7788	Flow Meter 5 to 60 L/min (2 to 15 US gpm)
	D2	1	8C-6874	Reducer
	D3	1	6V-9746	O-Ring Seal
	D4	1	124-1901	Permanent Coupling
	D5	3 ft	122-6870	Bulk Hydraulic Hose
	D6	1	124-2147	Permanent Coupling
	D7	1	6V-8942	O-Ring Reducer
	D8	1	6V-8556	Nut
	D9	1	6V-8398	O-Ring Seal
F		1	311-1362	Vacuum Cap
G		1	418-3610	Track Block

Position the machine on level ground.
Show/hide table

Illustration 5 g03414758

Sprocket (left travel)
(G) Track block
(1) Sprocket
Place track block (G) in sprocket (1) to block forward left travel. Refer to Illustration 5.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Show/hide table

Illustration 6 g02792728

Flow Meter Tool Layout
Tooling (D)
( 2) Case drain hose
(3) Connector
(4) Travel motor
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 6.
Disconnect case drain hose (2) from connector (3).
Connect the flow meter assembly (D) between connector (3) and case drain hose (2).
Note: Correct orientation of the flow meter is necessary. The oil flows from travel motor (4) to case drain hose (2).
Remove 311-1362 Vacuum Cap.

Start the engine.
Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF.
Place the hydraulic activation control lever in the UNLOCKED position.
Move the left travel lever to full FORWARD position and check the flow of oil through the flow meter. Refer to Table 1.
Remove track block (G) from sprocket (1).
Move the left travel lever to reposition the travel motor.
Place track block (G) in sprocket (1) to block forward left travel.
Repeat Steps 5 through 8 to obtain three measurements of case drain oil.