| |
| Illustration 1 | g06032288 |
|
Fuse Panel and ECMs are located behind Left Rear panel | |
| |
| Illustration 2 | g06041468 |
|
ECMs are located behind Left Rear panel (1) Machine ECM (2) Transmission ECM (3) Steering ECM | |
| |
| Illustration 3 | g06041462 |
|
(1) Fuse Panel
(2) Disconnect Switch | |
| NOTICE |
|---|
|
Replace fuses with the same type and size only. Otherwise, electrical damage can result. If it is necessary to replace fuses frequently, an electrical problem may exist. Contact your AVSpare dealer. |
| |
| Illustration 4 | g03826488 |
(F1) Electric Pump - 125 amp
(F2) Electrical System - 80 amp
(F3) Engine ECM - 20 amp
(F4) Spare - 10 amp
(F5) Grade and Slope ECM - 15 amp
(F6) Transmission ECM - 20 amp
(F7) Steering ECM - 20 amp
(F8) Machine ECM - 20 amp
(F9) Right Turn Signal - 5 amp
(F10) Left Turn Signal - 5 amp
(F11) Horn - 10 amp
(F12) Lights - 10 amp
(F13) Monitoring System - 10 amp
(F14) Brake Lights - 10 amp
(F15) Fuel and DEF Pumps - 30 amp
(F16) Start Switch and Steering ECM - 15 amp
(F17) Start Switch and Machine ECM - 10 amp
(F18) Spare - 10 amp
(F19) Alarm - 10 amp
(F20) Key Power to Grade and Slope ECM - 15 amp
(F21) DEF ECM - 30 amp
(F22) Diagnostic ECM - 10 amp
(F23) Product Link ECM - 10 amp
(F24) 12 V Power Receptacle - 10 amp
(F25) Electrical System - 10 amp
(F26) Beacon - 20 amp
(F27) Display - 15 amp
(F28) Hood Raise and Lower - 15 amp
(F29) Aftertreatment ECM - 15 amp
(F30) Start Switch - 7.5 amp
(F31) Start Switch and Rotor ECM - 15 amp
(F32) Side Plate Warning Lights - 10 amp
(F33) Truck Lights - 10 amp
(F34) Spare - 10 amp
(F35) Conveyor Raise/Lower - 10 amp
(F36) Spare - 10 amp
(F37) Spare - 10 amp
(F38) Work Lights 1 - 30 amp
(F39) Travel Lights - 15 amp
(F40) Work Lights 2 - 30 amp
(F41) Work Lights 3 - 30 amp
(F42) Start Switch and Electrical System - 10 amp
(F43) Lights - 10 amp
(F44) Spare - 15 amp
(F45) Work Lights 4 - 30 amp
(F46) Spare - 15 amp
(F47) Spare - 10 amp
(F48) Start Switch - 10 amp
(F49) Spare - 10 amp
(F50) Sensor Electrical System - 10 amp
(FS1) Spare - 10 amp
(FS2) Spare - 15 amp
(FS3) Spare - 15 amp
(FS4) Spare - 15 amp
(FS5) Spare - 10 amp
(FS6) Spare - 10 amp
(K1) Spare - Relay
(K2) Spare - Relay
(K3) Spare - Relay
(K4) Blower - Relay
(K5) Water Fill Pump - Relay
(K6) High-Pressure Wash - Relay
(K7) Conveyor Swing Left - Relay
(K8) Conveyor Swing Right - Relay
(K9) Right Grade Control Ski - Relay
(K10) Left Grade Control Ski - Relay
(K11) Spare - Relay
(K12) Conveyor Lower - Relay
(K13) Conveyor Raise - Relay
(K14) Moldboard Lower - Relay
(K15) Moldboard Raise - Relay
(K16) Fuel Pump - Relay
(K17) Spare - Relay
(K18) Spare - Relay
(K19) Action Alarm - Relay
(K20) Operator Horn - Relay
(K21) Alarm - Relay
(K22) Right Turn Signal - Relay
(K23) Left Turn Signal - Relay
(K24) Horn - Relay
(K25) Lights - Relay
(K26) Brake Lights - Relay
(K27) Anti-slab Raise - Relay
(K28) Anti-slab Lower - Relay
(K29) Anti-slab Lock - Relay
(K30) Spare - Relay
(K31) Tow Mode Parking Brake Solenoid - Relay
(K32) Tow Mode Auxiliary - Relay
(K33) Water Spray System - Relay
(K34) Starter Motor - Relay
(K35) Right Side Plate Warning Light - Relay
(K36) Left Side Plate Warning Light - Relay
(K37) Spare - Relay
(K38) Green Truck Light - Relay
(K39) Conveyor Fold - Relay
(K40) Conveyor Unfold - Relay
(K41) Red Truck Light - Relay
(K42) Work Lights 1 - Relay
(K43) Work Lights 2 - Relay
(K44) Work Lights 3 - Relay
(K45) Travel Lights - Relay
(K46) Spare - Relay
(K47) Spare - Relay
(K48) Beacon - Relay
(K49) Work Lights 4 - Relay
(K50) Electrical System - Relay
(K51) Electric Auxiliary Pump - Relay
(KS1) Spare - Relay
(KS2) Spare - Relay
(KS3) Spare - Relay
The Electrical System Schematic of the machine is shown in the Service Manual.
Refer to the appropriate media number below for the complete Electrical Schematic:
(S/N: JCF; LH9; 8RF; EL6) Machines refer to Electrical Schematic, UENR6397.
(S/N: JB9; JFC; LB8; FG4; TPH; XS6) Machines refer to Electrical Schematic, UENR6398.
(S/N: JB7; HN8; HC8; RL3; H6S; 626) Machines refer to Electrical Schematic, UENR8363.
(S/N: SL8; TLZ; ESE; AK5; AN8; EE2; E8S; 3C6; 627) Machines refer to Electrical Schematic, UENR8362.
The schematic will illustrate locations for all the electrical components and harness connectors that are installed on the machine.