349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Main Hydraulic Pump Caterpillar


Main Hydraulic Pump
`
1.1. Construction
2.2. Accessory Pump (If Equipped)
3.1. Operation

Construction



Illustration 1g06015228
Main pumps
(1) Port (pressure sensor)
(2) Outlet port (idler pump)
(3) Outlet port (drive pump)
(4) Port (pressure sensor)
(5) Proportional reducing valve (power shift pressure)
(6) Port (negative flow control pressure for drive pump)
(7) Port (negative flow control pressure for idler pump)
(8) Drive pump
(9) Case drain port
(10) Pilot pump
(11) Idler pump
(12) Inlet port (supply oil from the hydraulic tank)
(13) Outlet port (pilot pressure)
(14) Port (power shift pressure)
(15) Housing

The main pump consists of drive pump (8) and idler pump (11). The drive pump and the idler pump are contained in an integral housing. Both pumps are variable displacement piston pumps. The drive pump and the idler pump are identical in construction and operation.

Supply oil from the hydraulic tank enters inlet port (12). The single inlet port is common to both pumps. The drive pump delivers oil through outlet port (3). The idler pump delivers oil through outlet port (2). The idler pump is supplied oil from the head of pilot pump (10). The pilot pump delivers oil through outlet port (13).

Both the drive pump and the idler pump have a regulator as part of the pump control system. The flow control of the pumps is performed by the operation of the regulators. The control system is identical for both pumps.

Proportional reducing valve (5) for the power shift pressure is on the head of the main pump. The proportional reducing valve is controlled by the machine ECM. The proportional reducing valve controls the signal from the power shift pressure for both the drive pump and the idler pump.

Negative flow control pressure from the main control valve enters the drive pump regulator at port (6). Negative flow control pressure from the main control valve enters the idler pump regulator at port (7).

Case drain oil from the pump housing flows from port (9) to the case drain filter.

Accessory Pump (If Equipped)



Illustration 2g06048944

Operation



Illustration 3g06048975
Main pumps (sectional view)
(8) Drive pump
(10) Pilot pump
(11) idler pump
(11) Gear
(18) Drive shaft
(19) Drive shaft
(20) Gear
(21) Swashplate
(22) Plate
(23) Retainer
(24) Piston slipper
(25) Piston
(26) Barrel
(27) Port plate
(28) Passage

Gear (20) of drive shaft (19) meshes with gear (17) of drive shaft (18). Gear (17) and gear (18) have the same number of teeth. Drive shaft (19) of drive pump (8) is connected to the engine by a coupling. When the engine is running, drive shaft (18) and drive shaft (19) rotate at the same speed. Therefore, drive pump (8) and idler pump (11) rotate at the same speed.

Pilot pump (10) is directly connected with drive shaft (18).

Barrel (26) contains nine pistons (25). Piston slippers (24) are connected to pistons (25) by retainers (23). The piston slippers are pressed against plate (22). Plate (22) lies on swashplate (21). Barrel (26) is splined to drive shaft (19). As drive shaft (19) rotates, the barrel, the pistons, and the piston slippers rotate around swashplate (21).

The angle of swashplate (21) determines the length of stroke of piston (25). As the angle of the swashplate increases, the length of stroke of the pistons increases and the output flow of the pump increases. As piston slipper (24) rotates around the swashplate, the piston moves out of barrel (26). The piston draws oil from passage (28) of port plate (27) during this movement. As the piston slipper continues to rotate around the swashplate, the piston moves into the barrel. The piston delivers oil to outlet port (13) during this movement. The oil delivery from ports (2) and (13) flows to the main control valve.

Information System:

314F and 315F Excavators Machine Systems Swing System
314F and 315F Excavators Machine Systems Pilot System
814 Wheel Dozer Differential and Final Drive Oil Level - Check
814 Wheel Dozer Differential and Final Drive Oil - Change
816K Landfill Compactor Sound Information and Vibration Information
300.9D VPS Mini Hydraulic Excavator Machine Systems Return Hydraulic System
312F and 313F Excavator Machine Systems Swing System
990K Wheel Loader and 844K Wheel Dozer Machine Systems Seat - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Pilot Hydraulic System
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Main Hydraulic System
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Camshaft - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Speed Signal - Test
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Main Control Valve
300.9D VPS Mini Hydraulic Excavator Machine Systems Boom Hydraulic System
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Negative Flow Control System
300.9D VPS Mini Hydraulic Excavator Machine Systems Bucket Hydraulic System
300.9D VPS Mini Hydraulic Excavator Machine Systems Stick Hydraulic System
349D2 MHPU Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Main)
312F and 313F Excavator Machine Systems Travel System
Exhaust Gas Valve (NRS) for C7.1, and C6.6 Engines {5137}
316F Excavator Machine System Specifications Pilot Lines (Main Pump)
318F Excavator Machine Systems Front Lines
910K, 914K and 920K Compact Wheel Loaders Operation Information