Cylinder Head
`
C13, C15, and C18 Tier 4 Final Engines
[UENR3381]
C13, C15, and C18 Tier 4 Final Engines
Fuel Priming Pump and Primary Fuel Filter - With Water Separator
C13, C15, and C18 Tier 4 Final Engines
Electric Starting Motor
BASIC ENGINE
CYLINDER HEAD GP
3408E and 3412E Engines for Caterpillar Built Machines
Cylinder Head Valves
C15 Petroleum Generator Set Engines
Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
C15 Petroleum Generator Set Engines
Cylinder Head
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
3408E and 3412E Engines for Caterpillar Built Machines
Cylinder Head
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
Show/hide table
| |
| Illustration 1 | g02557638 |
|
Typical example Top view of cylinder head | |
Show/hide table
| Specification for 331-2478 Cylinder Head Gp and 302-2202 Cylinder Head Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| - | 26 | 242-1811 Bolt | Before assembly, lubricate the threads of the bolts and both sides of the washers with 4C-5593 Thread Lubricant.
Use the following procedure to tighten the bolts: 1. Torque bolt 1 through bolt 26 in a numerical sequence to 2. Torque again bolt 1 through bolt 26 in a numerical sequence to 3. Turn bolt 1 through bolt 26 in a numerical sequence to an extra 120 ± 5 degrees as shown in Illustration 1. 4. Loosen bolt 1 through bolt 26 to 5. Torque bolt 1 through bolt 26 in a numerical sequence to 6. Torque again bolt 1 through bolt 26 in a numerical sequence to 7. Turn bolt 1 through bolt 26 in a numerical sequence to an extra 120 ± 5 degrees as shown in Illustration 1. 8. Torque bolt 27 through 34 in a numerical sequence to |
| - | 8 | 210-4460 Bolt | |
| Top gasket face of cylinder block, cylinder liners, and bottom gasket face of cylinder head must be free of oil, fuel, water, and other contaminants before assembly. | |||
Show/hide table
| |
| Illustration 2 | g02558076 |
|
Top view of cylinder head | |
Show/hide table
| |
| Illustration 3 | g02558157 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| - | 35 | 3B-0623 Cup Plug | Installation depth (M) is |
| Installation depth (N) is |
|||
| Apply Loctite 11358 to the bores for the cup plugs prior to the installation. | |||
Information System:
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement
Diesel Particulate Filter - Remove and Install - Clean Emissions Module
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement
Diesel Particulate Filter - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
The Transmission Oil Must be Changed Before Replacing any Transmission Solenoids{3030}
2012/02/16
New Sheets and Liners Are Available In Order to Reduce the Temperature Inside the Cab on the 320D and 323D Hydraulic Excavators {1801, 7076, 7251, 7267}
G310B, G315B and G320B Demolition and Sorting Grapples
Hydraulic Cylinder - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Front Idler and Recoil Spring - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Track Adjusters - Assemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Track Adjusters - Disassemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Track Adjusters - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Sprocket - Remove and Install
Oil Leaks From the Sight Gauge Gp on Certain Excavators and Mobile Hydraulic Power Units{7479}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement
Fuel Manifold - Remove and Install - Clean Emissions Manifold
Salvage of Weld on Water-Cooled Exhaust Manifold for 3500 Series Engines {0679, 1059}
2010/03/22
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
2010/03/22
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
2010/03/22
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Electronic Control System
Symptom Troubleshooting
3516B Off-Highway Trucks
Engine Coolant Pressure Low
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement
Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
G310B, G315B and G320B Demolition and Sorting Grapples
Hydraulic Cylinder - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines
Turbocharger - Remove and Install - Low Pressure, For Series Turbocharger Applications
C15 and C18 Engines for Caterpillar Built Machines
Turbocharger - Remove and Install - High Pressure, For Series Turbocharger Applications
308D CR Excavator Machine Systems
Swing Drive - Remove
308D CR Excavator Machine Systems
Swing Drive - Install