W345B Series II Material Handler Machine System Specifications Stick Cylinder Caterpillar


Stick Cylinder
`



Illustration 1g02796237

Table 1
Specification for 196-4120 Stick Cylinder Gp    
Item     Qty     Part     Specification Description    
1     2     087-5548 Bushing     Inside diameter is 100.29 ± 0.02 mm (3.948 ± 0.001 inch).    
Installation depth in the cap assembly
9.8 ± 0.5 mm (0.39 ± 0.02 inch).
Installation depth in the rod assembly
10.0 ± 0.5 mm (0.39 ± 0.02 inch).
2     1     7Y-4695 Locknut     Before assembly, lubricate the face and the threads with 309-6932 Hydraulic Oil .    
Torque to
10800 ± 550 N·m (7966 ± 406 lb ft).
3     1     7Y-4697 Ring     Lubricate the inside diameter and the outside diameter with clean grease.    
4     1     9X-3601 Seal As     Lubricate the inside diameter and the outside diameter with clean grease.    
5     1     096-1581 Ring     Lubricate the inside diameter and the outside diameter with clean grease.    
A     1     196-4121 Cylinder As     Bore diameter is
150.00 ± 0.10 mm (5.906 ± 0.004 inch).    
B     1     196-4124 Rod As     Diameter is
104.930 ± 0.038 mm (4.1311 ± 0.0015 inch).    
C     1     358-8524 Head     Bore over two lands is
105.63 ± 0.03 mm (4.159 ± 0.001 inch).    
6     8     7Y-5215 Bolt     Torque to
900 ± 100 N·m (664 ± 74 lb ft).    
7     1     103-8380 Stop     Free linear movement of the stop after assembly is
0.50 ± 0.26 mm (0.020 ± 0.010 inch).    
8     2     095-0929 Retaining Ring     Maximum outside diameter after assembly is
70.4 mm (2.77 inch).    
9     1     5I-8516 Seal Ring     The slit of the seal ring must turn in the direction of the piston.    
10     1     114-0760 Bushing     Outside diameter before assembly is
110.148 ± 0.033 mm (4.3365 ± 0.0013 inch).    
Thickness is
2.475 ± 0.025 mm (0.0974 ± 0.0010 inch).
11     1     128-9265 Buffer Seal     Lubricate the sealing lightly with the lubricant that is being sealed.    
12     1     170-9864 U-Cup Seal     Lubricate the sealing lightly with the lubricant that is being sealed.    
13     1     165-9290 Lip Type Seal     Lubricate the sealing lightly with the lubricant that is being sealed.    
14     -     -     Before assembly, apply green Loctite Retaining Compound 620 to the wiper seal groove.    

Information System:

446B Backhoe Loader Transmission (Autoshift) Transmission (Autoshift)
385B Excavator Engine Oil and Filter - Change
312C Excavator 3064 Engine Supplement Muffler - Remove and Install
385B Excavator Engine Oil Level - Check
385B Excavator Engine Air Filter Primary Element - Clean/Replace
345B Series II Excavator Machine System Specifications Boom Cylinder
385B Excavator Cooling System Coolant Level - Check
325D and 329D Excavators Machine System Specifications Track Roller (Single Flange)
3126B Engine for Caterpillar Built Machines Throttle Position Sensor Circuit - Test
385B Excavator Cooling System Coolant (ELC) - Change
2002/07/08 New Final Drive Gp is Used for Improved Service Life {4050}
312C Excavator 3064 Engine Supplement Hood - Remove and Install
446B Backhoe Loader Transmission (Autoshift) Torque Converter
385B Excavator Fuel System Primary Filter (Water Separator) Element - Replace
446B Backhoe Loader Transmission (Autoshift) Transmission
385B Excavator Fuel System Secondary Filter - Replace
3500B Engines for Excavators Air Inlet and Exhaust Lines
325D and 329D Excavators and 325D Material Handler Machine System Specifications Track Adjuster
3126B Engine for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
5230B Excavator Hydraulic System Boom, Bucket, Stick, Swing and Travel Cycle Times
385B Excavator Hydraulic System Oil Filter (Pilot) - Replace
312C Excavator 3064 Engine Supplement Electric Starting Motor - Remove and Install - Engine In Chassis
385B Excavator Hydraulic System Oil Filter (Case Drain) - Replace
2001/07/23 New Dump Cylinder Tubes are Available {5057}