W345B Series II Material Handler Machine System Specifications Swing Drive - Left Swing Drive and Right Swing Drive Caterpillar


Swing Drive - Left Swing Drive and Right Swing Drive
`
1.1. Swing Drive Mounting



Illustration 1g01433764

Note: After installation of the four spring pins (1), create two stake marks lightly at a distance (A) from each spring pin.

(A) Distance from edge of the spring pin hole to stake mark ... 2.25 ± 0.75 mm (0.089 ± 0.030 inch)

(2) Apply 1U-8846 Gasket Sealant to the surfaces of the housing cover and ring gear before assembly.

(3) Torque for the hose assembly ... 18 ± 2 N·m (13 ± 1 lb ft)

(4) Shutoff valve

Torque for installing the shutoff valve ... 50 ± 7 N·m (37 ± 5 lb ft)
Torque for shutting the shutoff valve ... 5.9 ± 2.9 N·m (50 ± 26 lb in)

(5) Torque for the bolt ... 100 ± 20 N·m (75 ± 15 lb ft)

(6) Apply 4C-5599 Anti-Seize Compound to the surfaces in contact with the bearing and the roller bearing assembly.

(7) Apply 4C-5599 Anti-Seize Compound to the surfaces in contact with the bearing and the roller bearing.

(9) Lubricate the sealing lip of the two lip type seals with the lubricant that is being sealed.

Swing Drive Mounting




Illustration 2g01433778

(10) Torque for the two connectors ... 45.0 ± 4.5 N·m (33 ± 3 lb ft)

(11) Torque for the gauge pipe ... 60 ± 6 N·m (44 ± 4 lb ft)

Note: Apply 4C-4030 Thread Lock Compound to the threads of the bolts (12) .

(12) Torque for the 16 bolts ... 270 ± 40 N·m (200 ± 30 lb ft)

(13) Apply 4C-4030 Thread Lock Compound to the threads of the eight bolts.

Information System:

315C Excavator Machine Systems Pump Control - Install
345B Excavator Equipment Lowering with Engine Stopped
315C Excavator Machine Systems Pump Control - Remove
315C Excavator Machine Systems Main Control Valve - Install
5130B Excavator Fuses - Replace
5130B Excavator Fuel Tank Water and Sediment - Drain
5230B Excavator Reference Material
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Governor Actuator - Calibrate
320C, 322C and 325C Excavators Tool Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
120H and 135H Motor Graders Engine Air Filter Primary Element - Clean/Replace
5130B Excavator Fuel System - Prime
315C Excavator Machine Systems Pressure Reducing Valve - Remove and Install
315C Excavator Machine Systems Shuttle Valve - Remove - Auxiliary Control
315C Excavator Machine Systems Swing Drive - Remove
315C Excavator Machine Systems Swing Drive - Install
315C Excavator Machine Systems Shuttle Valve - Remove - Straight Travel
315C Excavator Machine Systems Undercarriage Frame - Remove
315C Excavator Machine Systems Shuttle Valve - Install - Straight Travel
315C Excavator Machine Systems Track Carrier Roller - Install
315C Excavator Machine Systems Undercarriage Frame - Install
315C Excavator Machine Systems Pilot Valve (Implement) - Remove
315C Excavator Machine Systems Pilot Valve (Implement) - Disassemble
315C Excavator Machine Systems Pilot Valve (Implement) - Install
315C Excavator Machine Systems Pilot Valve (Implement) - Assemble