Stick - 3.1 m (10.17 ft)
`
318F Excavator Machine Systems
[UENR5653]
IMPLEMENTS
STICK GP
318E Excavator Machine System Specifications
Stick - 3.1 m (10.17 ft)
318E Excavator Machine System Specifications
Stick - 2.6 m (8.53 ft)
318E Excavator Machine System Specifications
Stick - 2.9 m (9.51 ft)
316F Excavator Machine System Specifications
Stick - 2.6 m (8.53 ft)
316F Excavator Machine System Specifications
Stick - 2.2 m (7.22 ft)
318F Excavator Machine Systems
Stick - 2.25 m (7.381 ft)
318F Excavator Machine Systems
Stick - 3.1 m (10.17 ft)
Show/hide table
![]() | |
Illustration 1 | g06018440 |
Show/hide table
Specification for 491-3677 Hoe Stick Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bucket, and the cylinder pin bores. | |||
1 | - | - | The stick cylinder must be assembled in order to orient the grease zerk, as shown. |
2 | 1 | 107-9852 Pin As | Diameter is |
3 | 1 | 4I-4809 Pin As | Diameter is |
4 | 2 | 166-1495 Lip Type Seal | Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed.
Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. |
5 | 4 | 235-7679 Lip Type Seal | Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed.
Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. |
6 | 2 | 229-1096 Bushing(1) | Bore before installation is Installation depth is |
7 | 2 | 228-5614 Bushing (1) | Bore before installation is Installation depth is |
8 | 2 | 357-5709 Bushing(1) | Bore before installation is Installation depth is |
Show/hide table
(1) | Install the bushing in the bore so that the part number of the bushing is facing outward. |
Information System:
Procedure to Rework Main Frames of Certain 422F, 428F, 432F, 434F, and 444F Backhoe Loaders {7054}
312F and 313F Excavator Machine System Specifications
Pilot Lines
318F Excavator Machine Systems
Stick - 3.1 m (10.17 ft)
323F Excavator
Hydraulic System Oil - Change
323F Excavator
Hydraulic System Oil Filter (Case Drain) - Replace
320D2 GC Excavator Machine System Specifications
Air Conditioner Lines
323F Excavator
Hydraulic System Oil Filter (Pilot) - Replace
312F and 313F Excavator Machine System Specifications
Swivel Lines
323F Excavator
Hydraulic System Oil Filter (Return) - Replace
323F Excavator
Hydraulic System Oil Level - Check
312F and 313F Excavator Machine System Specifications
Swing Drive
318F Excavator Machine Systems
Stick - 2.6 m (8.53 ft)
312F and 313F Excavator Machine Systems
Electronic Control (Boom System)
312F and 313F Excavator Machine Systems
Shovel Crane - Test and Adjust
320D2 GC Excavator Machine Systems
Bucket Cylinder - Remove and Install
312F and 313F Excavator Machine Systems
Electronic Control (Stick System)
320D2 GC Excavator Machine Systems
Load Control Valve (Stick Cylinder) - Remove and Install
320D2 GC Excavator Machine Systems
Load Control Valve (Stick Cylinder) - Disassemble
312F and 313F Excavator Machine Systems
Electronic Control (Bucket System)
320D2 GC Excavator Machine Systems
Load Control Valve (Stick Cylinder) - Assemble
320D2 GC Excavator Machine Systems
Stick Cylinder - Remove and Install
320D2 GC Excavator Machine Systems
Stick - Remove and Install
312F and 313F Excavator Machine Systems
Electronic Control (Blade System)
Installation of the 418-7814 Auxiliary Hydraulic Lines Gp (Boom) on Certain Hydraulic Excavators {5057}