Swing Drive Mounting
`
312F and 313F Excavator Machine System Specifications
[UENR6163]
312F and 313F Excavator Machine System Specifications
Swing Gear and Bearing
312F and 313F Excavator Machine System Specifications
Swing Drive
HYDRAULIC SYSTEM
DRIVE GP
312F and 313F Excavator Machine System Specifications
Swing Drive Mounting
312F and 313F Excavator Machine System Specifications
Swing Drive
Show/hide table
| |
| Illustration 1 | g06018297 |
|
Top view Typical example | |
Show/hide table
| Specification for 425-7076 Swing Drive and Mounting Gp and 425-7084 Swing Drive and Mounting Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 1 | 8T-4191 Bolt | Torque to |
Show/hide table
| |
| Illustration 2 | g06018301 |
|
Section B-B | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 2 | 2 | 191-2543 Pin | Before assembly, apply Loctite C5A Copper Anti-Seize compound to the pin. |
| 3 | 1 | 5D-1026 Band Clamp | Assemble the band clamp to upper side to eliminate potential interference between clamp head and valve.
Torque to |
| 4 | 14 | 461-3872 Bolt | Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper anti-seize compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 55 ± 5 degrees. |
| 5 | - | - | Before assembly, the surfaces must be clean and free of protective coating. |
| 6 | 1 | - | Before assembly into the upper frame group, coat the mating surfaces with 8C-8422 Sealant. |
Information System:
318F Excavator Machine Systems
Stick - 3.1 m (10.17 ft)
312F and 313F Excavator Machine System Specifications
Swing Gear and Bearing
312F and 313F Excavator Machine System Specifications
Fuel Tank
318F Excavator Machine Systems
Stick - 2.25 m (7.381 ft)
312F and 313F Excavator Machine Systems
Electronic Control (Main Pump System)
312F and 313F Excavator Machine Systems
Electronic Control (Pilot System)
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Cylinder Head - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Flywheel - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Engine Oil Pump - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Turbocharger - Remove and Install
318F Excavator Machine Systems
Stick - 2.6 m (8.53 ft)
312F and 313F Excavator Machine System Specifications
Swing Drive
323F Excavator
Hydraulic System Oil Level - Check
323F Excavator
Hydraulic System Oil Filter (Return) - Replace
312F and 313F Excavator Machine System Specifications
Swivel Lines
323F Excavator
Hydraulic System Oil Filter (Pilot) - Replace
320D2 GC Excavator Machine System Specifications
Air Conditioner Lines
323F Excavator
Hydraulic System Oil Filter (Case Drain) - Replace
323F Excavator
Hydraulic System Oil - Change
318F Excavator Machine Systems
Stick - 3.1 m (10.17 ft)
312F and 313F Excavator Machine System Specifications
Pilot Lines
Procedure to Rework Main Frames of Certain 422F, 428F, 432F, 434F, and 444F Backhoe Loaders {7054}