415 Industrial Loader Hydraulic and Steering System Lift Arm Caterpillar

Lift Arm

415 Industrial Loader Hydraulic and Steering System [M0113211]

415 Industrial Loader Hydraulic and Steering System Lift Cylinder

IMPLEMENTS

ARM GP

415 Industrial Loader Hydraulic and Steering System Lift Arm

Show/hide table




Illustration 1	g06534329

Show/hide table

Table 1
Item	Qty	Part	Specification Description
Before assembly of the cylinders, apply black 5P-0960 Grease Cartridge to the bearings and pins . As required, use the following spacer in order to achieve maximum clearance of 1.0 mm (0.04 inch) between the arm and the tower.

1	2	128-7905 Spacer	Thickness of one spacer is 1.0 mm (0.04 inch) should be used to reduce gaps.
2	2	128-7903 Spacer	Thickness of one spacer is 3.0 mm (0.12 inch) should be used until gaps prevent fitment.
3	1	341-6152 Pin	Diameter is 59.926 to 59.974 mm (2.3593 to 2.3612 inch).
As required, use the following washers. Atleast one 3.0 mm (0.12 inch) washer should be used adjacent to each retaining ring
4	10	373-8390 Shim	Thickness of one shim is 1.0 mm (0.04 inch) should be used to reduce gaps.
5	13	7X-0542 Hard Washer	Thickness of one washer is 3.0 mm (0.12 inch) should be used until gaps prevent fitment.
6	2	360-2816 Pin	Diameter is 49.966 to 50.024 mm (1.9672 to 1.9694 inch).
7	4	531-3531 Bearing	Bore after assembly is 90.050 to 90.235 mm (3.5453 to 3.5526 inch).
8	1	362-3270 Pin	Diameter is 49.966 to 50.024 mm (1.9672 to 1.9694 inch).
9	1	362-3269 Pin	Diameter is 49.966 to 50.024 mm (1.9672 to 1.9694 inch).
10	6	9R-0411 Bushing	Bore after assembly is 45.238 ± 0.047 mm (1.7810 ± 0.0019 inch).
As required, use the following washers. Atleast one 3.0 mm (0.12 inch) washer should be used adjacent to each retaining ring
11	13	111-4337 Washer	Thickness of one washer is 1.0 mm (0.04 inch) should be used to reduce gaps.
12	10	9R-0158 Washer	Thickness of one washer is 3.0 mm (0.12 inch) should be used until gaps prevent fitment.
13	2	193-5914 Plug	Insert the threaded plugs when auxiliary lines are not fitted.
14	2	546-6477 Pin	Diameter is 44.966 to 45.024 mm (1.7703 to 1.7726 inch).
As required, use the following spacers in order to achieve maximum clearance of 1.0 mm (0.04 inch) between the arm and the bucket. Equalize shims to center the bucket on the lift arms.
15	3	363-2855 Shim	Thickness of one shim is 1.00 ± 0.20 mm (0.040 ± 0.007 inch).
15	2	363-2856 Shim	Thickness of one shim is 3.00 ± 0.20 mm (0.118 ± 0.007 inch).
16	1	360-2823 Pin As	Diameter is 44.95 to 45.00 mm (1.769 to 1.771 inch).
17	2	9R-5828 Bushing	Bore after assembly is 45.238 ± 0.047 mm (1.7810 ± 0.0019 inch).
18	1	360-2822 Pin	Diameter is 44.966 to 45.024 mm (1.7703 to 1.7726 inch).
19	1	364-3011 Pin As	Diameter is 54.95 to 55.00 mm (2.163 to 2.165 inch).