Installation Instructions for Jacket Water Heaters with Seal Kits{1383} Caterpillar


`
Installation Instructions for Jacket Water Heaters with Seal Kits{1383} [SEHS9969]
ELECTRICAL AND STARTING SYSTEM
HEATER GP
Installation Instructions for Jacket Water Heaters with Seal Kits{1383}
1.1. Introduction
2.1. Installation Instructions for Seal Kit
3.1. Installation Instructions for Jacket Water Heaters
Engines:
3054 (S/N: 7BJ1-UP; 5HK1-UP; 9RM1-UP)
3054B (S/N: 7SG1-UP)
3056 (S/N: 8XJ1-UP)
3114 (S/N: 2ZF1-UP; 5EF1-UP; 1ZG1-UP; 2FG1-UP; 4RR1-UP; 97Z1-UP)
3116 (S/N: 4TF1-UP; 2WG1-UP; 4PG1-UP; 1CK1-UP; 1SK1-UP; 9GK1-UP; 5EN1-UP; 2MR1-UP; 6RR1-UP; 98Z1-UP)
3126 (S/N: 55K1-UP; 6JK1-UP; 1WM1-UP)
3126B (S/N: BMA1-UP; 5GG1-UP)
3176C (S/N: 3PD1-UP)
3196 (S/N: 5ED1-UP)
3204 (S/N: 7YJ1-UP; 45V1-UP; 10X1-UP)
3208 (S/N: 90N1-UP; 01Z1-UP; 02Z1-UP; 03Z1-UP)

Introduction

This Special Instruction contains the necessary instructions in order to install the following Jacket Water Heaters: 3T-8724, 6N-9125, 7E-5244, 7E-6310, 9X-3294, 9Y-5316, 9Y-5318, 127-8603, 127-8605, 166-0658 and 194-7258.


NOTICE

You must read all of the instructions and you must fully understand all of the instructions within this article before you attempt any part of the procedure.


Installation Instructions for Seal Kit

The following procedure is recommended for installation of the following Seal Kits: 132-1448, 133-3413 and 161-8200. Refer to Table 1.

Table 1
Core Plug Bore Diameter     Seal Kit    
Ø 31.8     133-3413    
Ø 38.1     161-8200    
Ø 44.0     132-1448    



Illustration 1g00804700

Typical Installation Of Seal Kit

(1) Snap Ring. (2) Retainer Rings. (3) Spacer Ring. (4) Seal. (5) Heater Adapter. (6) Cap Assembly. (7) Cord Assembly.

  1. If necessary, remove old snap ring (1), retainer rings (2), spacer ring (3), and seal (4). Discard old parts.

  1. Clean heater adapter (5). Make sure that the heater adapter is free from dirt, grease, and any other debris.

  1. Install seal (4) onto heater adapter (5) .

  1. Install retainer rings (2) and spacer ring (3) .

    Note: Assemble retainer rings (2) on each side of spacer ring (3). Offset the teeth from each other and orient the teeth toward seal (4). Refer to Illustration 1.

  1. Install snap ring (1) .

Installation Instructions for Jacket Water Heaters

The following procedure is recommended for installation of the Jacket Water Heaters.




Illustration 2g00803515

Typical Installation Of Jacket Water Heaters

  1. Allow the engine to cool and drain the coolant.

  1. Remove the existing jacket water heater. If new installation is required, remove the appropriate cup plug from the bore in the block.

  1. Clean the bore in the block until the bore is free of any deposits.

    Note: If the outside edge of the bore is not chamfered, file any sharp edges.

  1. Remove cap assembly (6) from the heater.

  1. Apply a light coat of grease to seal (4) and to the bore.

  1. Place the heater SQUARELY into the bore. Ensure that the heater element is oriented correctly.

    Note: Do not wedge the heater into the bore because damage to the retaining rings and the seal may result. The heater element should not touch any walls.

  1. Once the heater has started into the bore, place a 1 1/4 inch deep socket over the threaded end of the heater. Insert the heater by lightly tapping the socket until the heater adapter seals against the block.

  1. Install cap assembly (6) onto the heater.

    Note: The cap assembly is used to protect the terminals when the cord assembly is disconnected from the heater.

  1. Fill the engine with coolant. Start the engine and check the engine for leaks. Continue to operate the engine until the operating temperature is reached in order to ensure that all of the air is purged from the cooling system.

  1. When the operating temperature is reached, stop the engine. Allow the engine to cool.

  1. Check the coolant level in the radiator or in the expansion tank. If necessary, top off the coolant.

  1. Remove cap assembly (6) from the heater.

  1. Install cord assembly (7). Hand tighten the final installation of the cord assembly. Energize the heater.

    Note: Always unplug the heater before starting the engine.

Information System:

322C Forest Machine Hydraulic System Relief Valve (Crossover) - Test and Adjust
322C Forest Machine Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Travel Counterbalance Valve
C-9 Engine for the 12H Motor Grader Excessive White Smoke
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Steering Control Valve
2001/06/04 Correction to Testing and Adjusting for 5230 Excavator {5072}
3046 Engine for Caterpillar Built Machines Valve Depth - Inspect
2001/06/04 Correction to Testing and Adjusting for 5230 Excavator {5072}
2001/06/04 Correction to Testing and Adjusting for 5130 Excavator {5072}
315C Excavator Hydraulic System Control Valve (Stick Lowering)
2001/06/04 Correction to Testing and Adjusting for 5130B Excavator {5072}
The Procedure to Install a Fuel Cooler on the 345B Excavator{1712}
315C Excavator Machine Systems Fuel Tank - Install
315C Excavator Machine Systems Pilot Valve (Oil Manifold) - Remove - NFC Limit Valve
2001/06/18 Special Instruction, SEHS9098-01, May 2001, "Installation Instructions for the 174-1508 Electric Motor is Now Available" {5927}
315C Excavator Machine Systems Main Hydraulic Pump - Remove
315C Excavator Machine Systems Pilot Valve (Oil Manifold) - Install - NFC Limit Valve
5230B Excavator Automatic Lubrication System Lubrication Injector Banks - Adjust
320C and 322C Forest Machines Hydraulic System Main Hydraulic System
Procedure to Install 189-8642 Water Spray Kit for Dust Control on PC6 and PC9 Cold Planers{5612}
CS56B, CP56B, CS66B, CS68B and CP68B Vibratory Soil Compactors Machine Systems Control Valve (Shift) - Disassemble
322C Forest Machine Machine System Specifications Boom - Log Loader
320C, 322C and 325C Excavators Tool Control System MID 069 - CID 1590 - FMI 03
5130B Excavator Engine Air Filter Primary Element - Clean/Replace