Installation of the 467-6748 Chassis Wiring Gp On Certain Hydraulic Excavators {6129} Caterpillar


`
Installation of the 467-6748 Chassis Wiring Gp On Certain Hydraulic Excavators {6129} [M0066408]
OPERATOR STATION
CONTROL GP-HYDRAULIC
Installation of the 467-6748 Chassis Wiring Gp On Certain Hydraulic Excavators {6129}
1.1. Introduction
2.1. Safety Section
3.1. Required Parts
4.1. Installation Procedure
Excavator
349D2 (S/N: PFD1-UP; TAH1-UP; SDM1-UP; RAN1-UP)
Hydraulic Kit
HYDRAULIC KIT (S/N: HKD1-UP)

Introduction

Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.

Safety Section

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.


------ WARNING! ------

Personal injury or death can result from sudden work tool movement.

Sudden movement of the work tool can cause injury to persons near the work tool.

To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.




Illustration 1g00104545

Prevent the machine from movement. Park the machine on a level surface.

Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch before you service the equipment . These warning tags (Special Instruction, SEHS7332) are available from your AVSpare dealer.

Required Parts

Table 1
Parts List for 467-6748 Chassis Wiring Gp Revision -00 
Item  Qty  Pt. No.  Part Name 
(1)  13  3S-2093  Cable Strap 
(2)  20  7K-1181  Cable Strap 
(3)  266-7379  Cable Strap 
(4)  467-7459  Chassis Harness As 
(5)  467-7460  Chassis Harness As 
(6)  204-1611  Strap 


Illustration 2g06017934
467-6748 Chassis Wiring Gp

Installation Procedure



    Illustration 3g06017950
    (AL-C1) Connect to Harness (6 poles): "E472 GN", "E404 B:U", "H833 PU", "M968 BU", "A464 GY"
    (EE-C3) Connect to Bucket IN Pressure Switch:: "A464 GY", "235 BK"
    (1) 3S-2093 Cable Strap
    (2) 7K-1181 Cable Strap
    (4) 467-7459 Chassis Harness As
    (5) 467-7460 Chassis Harness As

  1. Connect harness (4) at "AL-C1" to the main machine harness behind the cab.

  2. Route harness (4) along the frame.

  3. Connect the ground wire to the frame.


    Illustration 4g06018106
    (AL-C1) Connect to Harness (6 poles): "E472 GN", "E404 B:U", "H833 PU", "M968 BU", "A464 GY"
    (AL-C2) Connect to Harness (4 poles): "A464 GY", "E472 GN", "E404 BU"U, "235BK"
    (EE-C1) Connect to Harness (4 Poles): "A464 GY", "E472 GN", "E404 BU", "235 BK"
    (EE-C3) Connect to Bucket IN Pressure Switch:: "A464 GY", "235 BK"
    (4) 467-7459 Chassis Harness As
    (5) 467-7460 Chassis Harness As

  4. Connect harness (4) to harness (5).


    Illustration 5g06018004
    (EE-C2) Connect to Bucket Cylinder Head Pressure Sensor: "E472 GN", "235 BK", "E404 BU"
    (EE-C3) Connect to Bucket IN Pressure Switch:: "A464 GY", "235 BK"
    (2) 7K-1181 Cable Strap
    (5) 467-7460 Chassis Harness As
    (6) 204-1611 Strap

  5. Connect harness (5) at "EE-C3" to the "Bucket IN Pressure Switch" on the main control valve.

  6. Connect harness (5) at "EE-C2" to the "Bucket Cylinder Head Pressure Sensor" on the supply tube.

  7. Route harness (4) along the frame to the coupler control valves.


    Illustration 6g06018096
    (AL-C3) Connect to Quick Coupler Hold to Run Solenoid: "M968 BU", "235 BK"
    (AL-C4) Connect to Quick Coupler Unlock Solenoid: "H833 PU", "235 BK"
    (EE-C2) Connect to Bucket Cylinder Head Pressure Sensor: "E472 GN", "235 BK", "E404 BU"
    (4) 467-7459 Chassis Harness As

  8. Connect "AL-C3" of harness (4) to the Quick Coupler Hold to Run Solenoid.

  9. Connect "AL-C4" of harness (4) to the Quick Coupler Unlock Solenoid.

Information System:

Installation of the 486-0608 Coupler Control Ar on Certain Hydraulic Excavators {6129, 7332, 7405, 7557}
Installation Procedure for the <NOBR>330-2400</NOBR> Front Lines Gp on Certain Hydraulic Excavators {5057}
325F Excavator Machine Systems Stick - Install
Installation Procedure for the <NOBR>437-0403</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
Installation Procedure for the <NOBR>418-1101</NOBR> Chassis Wiring Gp On Certain Hydraulic Excavators {1408}
Installation Procedure for the <NOBR>416-5026</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
Installation Procedure for the <NOBR>330-2397</NOBR> Front Lines Gp on Certain Hydraulic Excavators {5057}
Installation of the <NOBR>501-2517</NOBR> Auxiliary Control Ar (Tool Control) on Certain Hydraulic Excavators {1408, 5051, 5057, 5059, 7301, 7405, 7557}
Installation of the <NOBR>501-2518</NOBR> Auxiliary Control Ar (Tool Control) on Certain Hydraulic Excavators {1408, 5051, 5057, 7405, 7557}
325F Excavator Machine Systems Stick Bearings and Seals - Install
325F Excavator Machine Systems Stick Bearings and Seals - Remove
325F Excavator Machine Systems Stick - Remove
300.9D VPS Mini Hydraulic Excavator Machine Systems Swing Hydraulic System
Procedure to Install a 455-6307 Gear Pump Group on Certain M318D MH and M322D MH Material Handlers {5073}
312F and 313F Excavator Machine Systems Return Hydraulic System
325F Excavator Machine Systems Drift Reduction Valve (Boom) - Remove and Install
Installation Procedure for the <NOBR>494-7661</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {5057, 5059, 5063, 7405, 7557}
Installation Procedure for the <NOBR>330-2550</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
Installation of the <NOBR>491-4423</NOBR> Auxiliary Control Ar (Medium Pressure) on Certain Hydraulic Excavators {5051, 5070, 5073}
Installation Procedure for the <NOBR>428-8276</NOBR> Pilot Lines Gp On Certain Hydraulic Excavators {5057, 5059}
Installation of the <NOBR>489-0498</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {1408, 5057, 5059, 5070, 5073, 7405, 7557}
Installation Procedure for the <NOBR>458-8259</NOBR> Front Lines Gp On Certain Hydraulic Excavators {5057}
Installation Procedure for the <NOBR>458-8260</NOBR> Pilot Lines Gp On Certain Hydraulic Excavators {5057, 5059}
Installation Procedure for the <NOBR>458-8261</NOBR> Pump Lines Gp On Certain Hydraulic Excavators {5057}