Serious injury or death by electrocution can result if the machine or attachments are not kept a safe distance from electrical power lines.
Keep the distance at least 3 m (10 feet) plus an additional 10 mm (.4 inch) for each 1,000 volts over 50,000 volts. For safety, local or state codes or jobsite operating directives, may require a greater distance.
Never swing a load over a truck cab or workers.
When swinging into a ditch, do not use the ditch to stop the swinging motion. Inspect the machine for damage if the boom is swung into a bank or an object.
Repeated chopping can cause structural damage. Use a digging, scratching or peeling motion when trying to penetrate rock, frozen ground or hard surfaces.
With certain boom-stick-bucket combinations, the bucket can hit the cab or front of the machine. Always check for interference when first operating a new attachment.
Whenever the wheels of the machine raise off the ground while digging, lower the machine back to the ground smoothly. DO NOT DROP OR AVSCH IT WITH THE HYDRAULICS. Damage to the machine can result.
Keep the stick out, when moving a clamshell machine, to prevent the bucket from swinging into the cab. The clamshell can swing in all directions.
Know the location of buried cables. Mark them clearly before digging.
Consult your AVSpare dealer for special teeth and side cutters available for use in severe applications.
Move the machine whenever the digging position is not efficient. The machine can be moved forward or backward anytime during the operating cycle.
To work in and out of close places, utilize the bucket, or other attachment to push or pull the machine, or to lift the wheels.
Use smooth, comfortable speeds while operating.
For efficient operation, use more than one control at a time when possible.
Spot a truck so the machine can load it from the rear or side. Load trucks evenly to avoid overloading the rear axles.
An oversized bucket or one equipped with blade-type side cutters, should not be used in rocky material. It slows down the cycle and damage to the bucket and other components could result.
- 1. Position the stick at a 70° angle to the ground.
- 2. Position the bucket cutting edge at a 120° angle to the ground. Maximum break out force can now be exerted with the bucket.
- 3. Move the stick in and keep the bucket parallel with the ground.
- 4. If the stick travel stops due to the load, adjust the depth of cut by raising the boom and/or curling the bucket.
- 5. To apply the greatest force at the cutting edge, down pressure must be decreased as the stick moves in.
- 6. Maintain the bucket so that it ensures a continuous flow of materials into the bucket.
- 7. Continue the pass with the bucket traveling in a horizontal direction, peeling material into it.
- 8. Close the bucket and raise the boom at pass completion.
- 9. Engage the swing control when the bucket is clear of the excavation.
- 10. To dump, move the stick out and open the bucket in one smooth motion.
Do not exceed the rated load capacity of the machine. If the machine is not on level ground, load capacities will vary.
Use short slings to prevent excessive load swing.
Damage to bucket cylinder, bucket or linkage could result if slings are placed incorrectly.
Use the sling lug on the back of the bucket to lift objects. Lifting capacities are calculated using lift hook without bucket. Adjust to this accordingly.
If the sling lug at the bottom of the backhoe bucket is used, the connection must be made by means of a shackle or clevis.
An unstable condition can exist if a load exceeds the machine load rating or, if a heavy load is swung over an end or side.
Picking up a load over a corner or lowering the blade or stabilizer are the most stable positions.
For the best stability, carry a load close to the machine and close to the ground.
Lift capacity decreases as the distance from the swing centerline is increased.
The clamshell can swing in all directions. Personal injury can result if it swings into the cab, or a person in the work area.
When traveling, use the clamshell restraint bracket, if equipped.
When moving over a rough surface, keep the stick out to prevent the clamshell from swinging into the cab.
Use hydraulic controls smoothly to avoid excessive clamshell swing.
- 1. Lower the clamshell bucket into the excavation with the stick in a vertical position.
- 2. For best penetration, apply down pressure as the bucket is closed.
- 3. Raise the boom when the bucket is fully closed.
- 4. When the bucket clears the excavation, engage the swing control. Operate the control smoothly to avoid excessive clamshell swing.
- 5. Begin opening the bucket slowly when approaching the dump area. Stop the swing or stick motion slowly and open the bucket fully.
- 6. An experienced operator can use the swinging momentum of the load to cast material for a faster cycle, and to move material farther away from the excavation.
Using bucket teeth to pick up an object can result in tooth or bucket damage.
Trap objects in the bucket for a sure pickup.